Go to http://192.168.1.1.
- Username: tmadmin
- Password: tmadmin
Then you will see this above page. Go and click at the WAN Tab and click at PPP.
Set the new interface as:
- PPP interface = 0
- ATM VC = aal5-0
- Protocol = PPoE
- Use DNS = enable
- Security = PAP
Don’t forget to set your username as USERNAME@streamyx and also your TMNet Streamyx password. When done, click Submit.
Click on ATM VC and make sure interface are set as:
- aal5-0 VPI = 0
- VCI = 35
- MUX = LLC
- Max proto = 2
After that, click on Admin and then Commit and then Reboot Once it’s done you should check your Internet connectivity by loading your favorite website.
If you’re unable to go to 192.168.1.1, please make sure that your PC IP is in the range of 192.168.1.x.
Done!
hi, saya ada masalah nak connect through wifi.
im using riger modem, then dirct connect to my zyxel wifi rouy\ter, bila nak connect, akan keluar, ‘local only” meaning that no internet acces.. then my fren kata kena ubah from pppoe to dhcp, how to do that???
if possible kalau u can ym with me then consult me, sebab dah berlarutan lama, memang just dialing aje yg boleh lepas through internet, wireless jadi local only.. help…
azree,
make sure your cabling is correct. from the modem to the router, connect through the WAN port. make sure both DHCP Server is enable on modem and router.
settings:-
modem (bridge mode, DHCP server enable, NAT disable)
router (router mode, PPPoE, DHCP server enable, NAT enable)
just browse the pages in both the modem and the router and find the things listed in the brackets. everything should work.
ym is not an option due to the fact when you need to ‘Apply’ a setting, your internet will be disconnected and you’ll loose all the discussion for reference..
good luck.
hi syakir ,
i plug DB102 to Prolink SW800AI 8 port switch and my 2 notebook with ethernet cable all together , setup with window XP ICS , but only one can connect at a time , the other cannot , please teach me how to make it both can share connection same time , tq .
i use Prolink SW800AI 8 ports switch to connect 3 computers and DB102 streamyx modem and setup by window XP using network setup wizard (ICS) , i can sharing the folders and printer but during connect to internet , i can only connect one computer at a time , cannot share the other two . pls tell me why and teach me how to fix it , tq
hmm…you sure are genius! where did u learn all of this bro?
Bro..
Need your expert assistance.
My setup:
Modem: Riger DB102 modem
IP: 192.168.1.1
Wireless router: Belkin Wireless N+ (F5D8235-4)
IP: 192.168.1.2
As you can see, both modem + router are in same IP segment of 192.168.1.x. My PC also in the same IP segment of 192.168.1.x.
My issue:
I can’t seem to be able to Ping the modem. I’d like to login & manage the modem wirelessly. I have no issue if i connect direct to the modem (using the LAN port)
why I need to login to the modem? I’m subscribed to 4MB Streamyx from tmnut. sometimes, my connection is super slow, and when I login to the modem through the LAN port, I can see that I’m subscribed to a 2MB package. Then.. after case log to tmnut, issue reolved, I can see the status shows as 4MB again. It’s annoying if I hv to physically connect to the LAN port instead of through WiFi.
hi.
its me again.
1 question, where do i tick the NAT?
simman,
Disable ICS and follow the tutorial above. you should able to get 2 laptops (or more) online in no time.
Big E,
With the current settings, you WILL NOT able to login to the modem directly. Eventhough the modem and router is in the same IP segment, they are being isolated using different ports (WAN & LAN) which only linked using a routing table. To check your DSLAM settings, you need to use a direct cable to the modem. There is no workaround for this unless you disable the WAN port on the router and plug-in the cable from the modem into the LAN port which I don’t recommend because the router will be useless (the modem will become the router and the router only functional as a switch).
idris,
The NAT option is supposed to be somewhere around the page where you enter the username and password for Streamyx.
Tq bro..
sigh.. I’ll hv to physically connect to the modem every time my connection suffers a snail crawl..
the operation status says, link down. i already refresh the page and still link down. what to do?
idris,
Link down means your PPPoE is not connected. the usual problem is wrong username@streamyx or password. please double check. better yet, you can take a screenshot and leave your email here so I can contact you later.
Cheers!
Ok here are some screen shots.
This is the default home page.
http://img13.imageshack.us/img13/7528/80199985.png
then i went to the WAN page. Open up PPP interface and filled in exactly like u said. like this
http://img5.imageshack.us/img5/9799/28539718.png
then after i pressed submit, sometimes the page doesn’t go anywhere, or the PPP interface is accepted but the link is down.
so what is my problem? and tell me what to do after the link is up. after commit and reboot, should i turn it off and plug in the cable into router or what? tell me everything please. i’m soo desperate. tell me step by step. with pictures if you can. thank you very much!
this is my email. iakmal@hotmail.com
hi idris,
USE DHCP = ENABLE
MTU = 1492
TICK at NEVER TIMEOUT
double check your ATM VC make sure it’s 0 / 35
Please submit your front page of the router after you did all the settings just to make sure everything is in the right order
anyway, what’s the network setup are you trying to do here? 1 modem to switch to multiple PC right? no standalone router right?
ok. after i did what you told me to, its still link down.
ok the page looks like this.
PPP interface page.
http://img19.imageshack.us/img19/1999/27280974.png
Router home page.
http://img12.imageshack.us/img12/452/68206581.png
then what?
my network setup? its from 1 modem (riger) to a wireless zyxel router.
and yes its a standalone router i think.
Hi Idris,
Go to the EOA page and delete the eoa-0 connection. Commit & Reboot once. I think that’s your problem. Please revert here if everything is solve.
OH MY GOODNESS……
It WORKS.
i didn’t even delete the eoa-0. changed some of my settings and it worked.
u helped me so much.
THANK YOU !!!!!!
hi,i have the same problem as iris.. it seems like the eoa-0 could not be deleted. “Error: The interface is being used as a bridge port”. i have tried evthing on top.. but always ‘link down’. hope u can solve my problem, ty a lot!
idris,
You are welcome. But according to your network devices, I highly recommend that your Zyxel Wireless Router handles the PPPOE rather than the Riger modem. Here’s my advice.
Riger Modem (Bridge – No setting needed to be done) connected to Zyxel Wireless Router WAN port (PPPoE – Streamyx password is entered here) then to Switch/PCs/Laptop
Arthur,
You need to make it as router mode first, enable the ppp-0 then only then can disable/delete the eoa-0. Please commit & reboot once after finish configure everything above.
ppp-0 = pppoe/pppoa
eoa-0 = ethernet over atm/bridge mode
if you don’t want to delete it, you just need to disable it, somehow
hi,
i have same problem like Arthur and idris
not able to go for pppoe mode
help me
Hello Dan,
Please follow through all the comments and at least ask questions in detail so I can help you better.
hi,
i m already trying all these steps, all the post by u, idris are carefully read and applying and re-trying pppoe connect my router several times but not working.
on first day i install the bridge mode connection
after an hour i change it on pppoe mode. than working fine. all night going well.
next day automatically data light become off. from that day till today i m trying pppoe several times but not working.
bridge mode work sucessfully,
many times i reset the router and go pppoe with ur steps which u have
wrote here.
but i m fail till now.
help me syakir
Hello Dan,
Please take a screenshot of the mainpage AFTER you set the PPPoE and the PPPoE page (the page you key in your user/pass) aswell. Easier to troubleshoot.
Will try to help as much as I can
hi, Syakir
here are the screen shots
http://img13.imageshack.us/img13/8403/atmvcj.jpg
http://img13.imageshack.us/img13/2052/bridgemoded.jpg
http://img13.imageshack.us/img13/9056/dslstatust.jpg
http://img13.imageshack.us/img13/6500/pppz.jpg
http://img13.imageshack.us/img13/5848/pppoemodeu.jpg
http://img13.imageshack.us/img13/9899/quickconfil.jpg
http://img13.imageshack.us/img13/2072/smartconfige.jpg
http://img13.imageshack.us/img13/9083/syaytemmoden.jpg
http://img13.imageshack.us/img13/2281/userconfigt.jpg
Thx for this “Will try to help as much as I can
”
Hi Dan,
Do not use the ’smartconfig’ or any other config tools they give. Just delete the eoa-0 and follow the above instructions.
You need to disable/delete your eoa-0. Commit & Reboot. And then recheck your ppp-0 settings (username/password) back. Enable DHCPD for that interface.
That should work. Whatever you do, please delete the eoa-0. You can enable it by pressing the magic ‘reset’ button or factory setting if one day you decided to be on the Bridge again.
Get back here and let me know the result.
Hello Syakir,
Thank You So Much..
I am really thankful to you for helping me configure my router.
hope to keep in touch.. God Bless You..
Hi Dan,
You are most welcome.
thanks for replying Syakir.
so, how are you?
i am fine. thank you.
I have done all step required and I’m sure i didn’t miss any step..
Here is the problem..
My house has 2 db102 modem running, with each different line.
However, this 2 modem cannot be in PPPoE mode in same time, either 1 is unable to connect to internet if both are in PPPoE mode.. Even technician from streamyx couldn’t help..
Few months ago, I backup the configuration of another modem and loaded it into my modem, is this the cause of ‘this problem’? Thanks a lot.. looking forward your answer..
Hi Author,
Please make sure each modem is using different user ID for Streamyx. One login can only connect once. Other than that, make sure both modem is not connected to the same network or not it will mess up the routing.
haziq,
I got some problem with my riger router..my problems is..
i want to set my Counter-Strike Condition Zero game server
to my riger..and howto do that..hope someone will help me
about this..you just can add me at YM…
“haziq_apc@yahoo.com”
haziq,
to make everything easy, use the DMZ function. just point it to your computer IP address.
hi,
i am using riger db 102 modem, the default is auto connect but now i don’t want use auto, i want manual connect, how to cancel the auto connect part?
thanks
mike
Hello Mike,
Just press the reset button for few seconds. It should reverted to the default ‘Bridge’ mode.
hi syakir.hope that u can help me here.there is a problem with my streamyx connection.before this i’m using pppoe configuration for my riger db102 modem but after some time (about 9-10 hours) it will suddenly disconnected.it happens everyday and i have to restart the modem everyday to get the connection back.this is not happening when i’m using manual connection and why is that?is there any other configuration that i should know?
to my experience, the ‘router’ is not up to the task of being ‘the’ router. it was built to be a modem (bridge) mode only. the router function is just an additional software to cramp the memory of the modem itself. there’s no configuration to overcome this. by making it a router mode, it will get hot fast. unless you have a special ventilation for the device.
my advice, get another standalone router (i use linksys wireless router) and connect the modem to another router. then fire away!
hi k.thanks for the reply.so you’re saying that the riger modem is just a ‘wannabe’ router la….and yeah..i’ve noticed that when i changed the configuration pppoe(auto) into manual connection, i’ve lost some speed.1 more thing, i forgot to tell u that when the last time i’m configuring my modem into pppoe mode, i’m using the ’smart configuration’ and not by configuring through the WAN tab.is there any difference?or was that why i’m keep getting disconnected?
thanks in advance.
hi zoey,
using smart configuration shouldn’t be much different from setting it manually. if you are having frequent disconnection, maybe you need to check your phone line. there’s so much possibilities of why the frequent disconnection can occur.
cheers
…
syakir.ak pkai streamyx billion adsl/router yg tmnet bg ni.
ak da setting autoconnect ikut PPPoE.
now baru beli wireless router ZyXEL sbb nk connect 3 pc kt uma ni.
then,,nape tym ak nk setting ZyXEL tu gne http://192.168.1.1 xbleh ek.cable ak da sambung betul da.bile ak connect cable dr pc ke ethernet wirelees router,n dr modem billion ke Wan Port ZyXEL,connection status terus jadi limited and no connectivity.
hope anybody can help
jon,
please refer to all the comments above. you need to reset back your modem into Bridge Mode. connect your modem to the WAN port on Zyxel Wireless Router. make sure both DHCPD is turn on.
halo bro.after going through lots of forum and comments from other riger user i came down to conclusion that the riger db102 modem is the most problematic modem given by Tmnet.its nothing to do wth my streamyx connection or other things.the modem just cannot support its full potential as a ‘router’.it’ll went weng-weng…pening…and all sort of penyakit after you switch it on for too long in pppoe mode.
anyway…thanks for all your advises bro.Salam…
kinda agree with you there zoey. i just sign up to streamyx combo package and they gave me the free wifi modem router. but guest what ? the security for wireless only support WEP. hahah. darn !
the DB102 modem is even worst. bad UI, no Dynamic DNS option. no DOS attach protection !!
syakir, if you can, please show the step by step to setup the DMZ.
let say the static is : 192.168.1.100
riger modem ip : 192.168.1.1
my wifi AP : 192.168.1.254
my connection
TM > modem > wifi (LAN PORT) *WAN Port got struct by lightning* hehe** so to use the wifi ap as dialer is not an option.
i’ve configured the modem for auto-dialer. done that. no problem with that. DHCP using the wifi ap, not the modem.
DHCP settings : default router > 192.168.1.1
default dns : 202.188.0.133 & 202.188.1.5
no problem with DHCP (through wireless) to connect to internet (using it now). just wanna open DMZ for the server. tq
many thanx in advanced.
Hi NakaLsKiT,
To enable the DMZ, find the DMZ function within the modem and the AP. since you use the LAN port for the modem on the AP, you’ll be needing to set the static IP both on modem and AP DMZ if the client is using WiFi.
I don’t think there’s a DMZ on the modem, you need to do a port forwarding on the modem to the static IP. Try searching ZXDSL modem howto on the forwarding. The firmware is the same.
Cheers.
salam bro…i’m happy all this while when suddenly this problem occured..it disconnected automatically..even worst,it can be set like it used to be..i mean the setting that u thought b4 wont work..link down,the data light wont blink…it also stated auth failure..whats that?
help me brothers…….
My i know how to set ADSL DB102 modem to run in auto connection…
@alfa: it’s time to call our beloved ISP, TMNet! either need to replace the modem or something wrong with the circuit.
@jay: auto connection??
Hi,
I would like to ask a question. I have a ADSL DB102 modem, and i want to connect it to 2 PCs. How do i do it??
buy a switch
i use db102 riger modem. connect with router 24-port. 1-5 pc can connect but pc6 and above can’t.please answer what happen.
check your network card. can the pc communicate the other computers? can it ping the router? usually this is because the port is faulty.
hi..im just wondering if you could help me out here. i had been struggling with this riger db108-wl modem, i rechecked all the cables’ connections and when it comes to installing it with a cd..im always stucked at step number 3!! i did try resetting it. i configured everything and there it goes again. oh how i wasted 6 hours of my life!
hello dith,
u don’t need the installation disc to configure anything. it’s just going to messed up your life if you do. just plug in all the cables involved and configure via web browser is much more easier than using the installation disc. that model is an actual wireless router + modem. so this how to is not suitable. just make sure you tick the NAT option and you’re ready to go!
cheers.
erm hello, i have a problem on my riger db 108WL modem. I recently installed I cant seem to enter the modem interface when i type 192.168.1.1. It keeps giving me a bad request page. Pls i seek guidance. Tho my internet is still working and my modem is connected to a 8-port router which is also connected to 6 pcs. TY
Hi Jack,
If I were you, I’ll reset the modem to the factory setting and see how it goes from there. The modem is built with dirt cheap component. Don’t expect it will survive very long. Since we’re using the modem without turning it off at all, expect for the worst.
Hello Syakir,
i have the same problem the modem suddenly crashed and have to change the operation mode to bridge to connect internet. After connecting through bridge for couple of hour, the data LED is on. Does it solve the problem. (FYI, im using RIGER db102 ADSL modem)
Hi Deneb,
I think the modem is dying. Firmware seems to be unstable. Use while you can, and when the time comes, just replace it for free!
Hi syakir…
gotta ask 1 question…
im using the same modem above, but instead of connecting to router, im using a switch.
until recent, i dont have to key in my password/username before connect to internet…in other words it was autoconnect.
my question, how can i set back the streamyx username/password so that i need to key in them before connecting to internet?
really need your help…if you need the screenshots, do tell me…im ready to show them…
thanks syakir
owh 1 more thing syakir…im sharing the connections with my friends…thats why im using switch…
arepeaceDNA,
if you reset the modem to it’s original state (bridge mode), then you’ll need a computer to be as a gateway. just press the reset button behind the modem and it will be on bridge mode.
then on your computer, set the dialing mode, then share the connection
.
My Riger router will set 2 wireless connection automatically.. One with the password and another one is without the password. Can i change it to one wireless connection? More and more users are connecting my router.. I even set 6 channel only but it seems like no difference also… Can someone give me some advice?